|
|
|
South Carolina Department of Natural Resources
South Carolina Wildlife Federation
National Rifle Association
Gun Owners of America
Africa News
US Department of State Travel Information
|
THE ACCURACY OUTFITTER We are fortunate to have Kenny Jarrett as a Member of the SCI Low Country Chapter. Kenny is well know among serious riflemen and hunters around the world as the "Father of the Beanfield Rifle."He was Championship Benchrest rifle shooter and a number of his Benchrest Records still stand today. He knows how to build extremely accurate and reliable hunting rifles.Kenny has kindly offered to share some tips on proper rifle cleaning and cold weather hunt preparations. This is the same information that he presents in his Gun Cleaning Seminars each year at the SCI National Conventions.To learn more about ordering your own Jarrett rifle, or booking a hunt on Kenny's 10,000 acre Cowden plantation, give Kenny a call at 803-471-3616 or visit his website at www.jarrettrifles.com
RIFLE CLEANING INSTRUCTIONS1. RUN 1 PATCH, WET WITH SHOOTER'S CHOICE, THROUGH THE BORE.2. WET A BRUSH WITH SHOOTER'S CHOICE , THEN RUN IT THROUGH THE BORE APPROXIMATELY 10 TIMES.3. RUN 2 PATCHES WITH SHOOTER'S CHOICE AGAIN TO CLEAN OUT ANY DIRT LEFT FROM BRUSHING IT OUT, THEN RUN 2 DRY PATCHES THROUGH AGAIN TO DRY THE BORE.4. RUN 2 PATCHES SOPPING WET OF SWEET'S SOLVENT THROUGH THE BORE AND LET STAND FOR APPROXIMATELY 10-15 MINUTES.*****5. RUN 2 DRY PATCHES THROUGH THE BORE TO DRY AFTER SWEET'S SOLVENT.6. IF THE PATCHES COME OUT WITH A FAIR AMOUNT OF GREEN (MELTED COPPER) A SECOND BRUSHING WITH SHOOTER'S CHOICE IS RECOMMENDED.7. SWAB OUT THE CHAMBER WlTH A BORE MOP.8. APPLY SHOOTER'S CHOICE TUBE GREASE TO REAR OF LOCKING LUGS OF BOLT AND DAB ON THE HELIX CURVE, ON THE REAR OF THE BOLT (COCKING CAM).******DO NOT LET SWEET'S SET IN BORE FOR OVER 30 MINUTES. SWEET'S WILL ETCH THE BORETRIGGER MAINTENANCE
THE FOLLOWING PROCEDURE SHOULD BE DONE AT EVERY OTHER CLEANING OR WHEN THE RIFLE HAS BEEN EXPOSED TO A LOT OF MOISTURE.1. PLACE THE RIFLE IN A PADDED VISE AT A HORIZONTAL POSITION, REMOVE THE BOLT AND SQUIRT LIGHTER FLUID INTO THE TRIGGER. LETTING IT DRIP OUT THE BOTTOM.2. REINSTALL BOLT AND DRY FIRE-SEVERAL TIMES THIS WHOLE PROCEDURE SHOULD BE PREFORMED AT LEAST TWICE.3. LET THE LIGHTER FLUID EVAPORATE, THEN REINSTALL BOLT.4. CAUTION: DO NOT SUBSTITUTE THE LIGHTER FLUID WITH ANY OTHER SOLVENT. THE LIGHTER FLUID WASHES AWAY MOISTURE AND FOREIGN MATERIAL AND LEAVES A MICROSCOPIC LUBE COATING.EXTREME COLD TREATMENT
1. REMOVE BOLT FROM THE RIFLE, ATTACH A FIRING PIN ASSEMBLY REMOVAL TOOL (WE SELL THEM) AND SIMPLY UNSCREW THE WHOLE FIRING PIN ASSEMBLY. IT ALL COMES OUT TOGETHER AND NO PARTS TO FALL OFF OR LOSE.2. PURCHASE A CAN OF AEROSOL BRAKE CLEANER AT THE PARTS STORE, SPRAY THE WHOLE ASSEMBLY SEVERAL TIMES UNTIL YOU ARE SATISFIED ALL LUBRICANTS HAVE BEEN REMOVED.3. LET IT COMPLETELY DRY AND REINSTALL IT IN THE BOLT BODY AND REMOVE TOOL.4. DO THE TRIGGER CLEANING PROCEDURE THOROUGHLY.DON'T FORGET TO RE-LUBE THE FIRING PIN ASSEMBLY AFTER YOUR COLD WEATHER HUNT.
|
This site is best viewed with Microsoft Internet Explorer and an 800 x 600 monitor screen setting.Send mail to
scilowcountry@yahoo.com with
questions or comments about this web site.
|
